KTI Networks Switch 10/100/1000 Base-T Guida di Installazione

-1-DOC.050724KGS-2402Web Samrt 24-Port Gigabit Ethernet Switchwith SFP supportInstallation Guide

-10-2. Installation2.1 Safety CautionsTo reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe thefollowing p

-11-2.5 Port and CableConnection Cables10/100M copper connection Cat.3, 4, 5, Cat.5 is recommended1000M copper connection Cat. 5, 5e, Cat. 5e is recom

-12-3. Operation of Web-based ManagementThe steps to start web management are:1. Type http://192.168.1.1 in the address row in a browser.2. Type passw

-13-3.1 Web Management Home OverviewThe Information of Page LayoutTop sideIt shows the front panel of the switch. In the front panel, the linked ports

-14-3.2 ConfigurationEach of them will be described in detail orderly in the following sections.

-15-3.2.1 System ConfigurationThe switch supports manual IP address setting. When IP address is changed, you must reboot theswitch to have the setting

-16-3.2.2 Ports ConfigurationParameter description:Mode Set the speed and duplex of the port. Speed/Duplex is comprised of the combina-tion of speed m

-17-3.2.3 VLAN Mode ConfigurationThe switch supports Port-based VLAN and 802.1Q Tag-based VLAN. Support 24 active VLANs andVLAN ID 1~4094.Parameter de

-18-3.2.4 VLAN Group ConfigurationIt shows the existed information of VLAN Groups List and maintains them, i.e. modify and delete oneof them. You can

-19-Add a Tag-based VLAN group<Delete Group> Just tick the check box (t) beside the ID, then press the <Delete Group> buttonto delete the

-2-(C) 2005 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced inany form or by any means or used to make any dire

-20-3.2.5 PVID ConfigurationThis configuration is applied to Tag-based VLAN mode only.Parameter description:Port 1-24 Port number.PVID This PVID range

-21-3.2.6 Aggregation ConfigurationThe Aggregation (Port Trunking) Configuration is used to configure the settings of Link Aggregation.You can bundle

-22-3.2.7 Mirror ConfigurationMirror Configuration is to monitor the traffic of the network. For example, we assume that Port A andPort B are Sniffer

-23-3.2.8 Quality of Service ConfigurationFunction description:Default Class Some packets which did not belong to the selected QoS classifica-tion met

-24-3.2.8.1 Vlan Tag ConfigurationParameter description:Port Port 1 ~ Port 24 - User can set up the port (1~24) respectively to let Vlan Tag QoSfuncti

-25-3.2.8.2 IP ToS ClassificationParameter description:Port Port 1 ~ Port 24 - User can set up the port (1~24) respectively to let IP ToS QoSClassific

-26-3.2.8.3 IP TCP/UDP Port ClassificationIn L4 QoS Configuration, you can select one of these special network transmission events with theassociated

-27-Advanced Mode:Special TCP/UDP class:Class assigned to the configured Custom Port numbersHigh - High PriorityLow - Low priorityDefault class (all o

-28-3.2.8.4 IP Diffserv ClassificationIP Diffserve Classification method uses 6-bit field of DSCP in an IP packet to classify the priority classof the

-29-3.2.9 Bandwidth ManagementBandwidth Management function is used to set up the limit of Ingress and Egress bandwidth for eachport.Note:Each port of

-3-The information contained in this document is subject to change without prior notice. Copyright (C). AllRights Reserved.TRADEMARKSEthernet is a reg

-30-3.2.10 Trap Event ConfigurationThe Trap Events Configuration function is used to enable the switch to send out the SNMP trapinformation while pred

-31-3.2.11 Max. Packet LengthThis function is used to limit the maximum packet length accepted by each port.Jumbo Frame(bytes) Set up the maximum leng

-32-3.3 MonitoringThere are two functions contained in the monitoring section.3.3.1 Statistics OverviewThe function of Statistics Overview collects an

-33-3.3.2 Detailed StatisticsParameter description:Rx Packets The counting number of the packet received.RX Octets Total received bytes.Rx High Priori

-34-Rx 65-127 Bytes Number of 65 ~ 126-byte frames in all packets received.Rx 128-255 Bytes Number of 127 ~ 255-byte frames in all packets received.Rx

-35-3.4 MaintenanceThe functions are supported:Status Display all configuration and status of the switchWarm Start Perform a reboot for the switchFact

-36-Each of them will be described in detail orderly in the following sections.System StatusProduct Name: To show the product name of this device.Firm

-37-MirrorSniffer Mode: Display the status the activation or deactivation of Port Mirror function.Sniffer Port: Display the port for monitoring.Source

-38-3.4.3 Factory DefaultFactory Default function can restore settings back to factory default values except the IP addresssettings.Note:Function Curr

-39-3.4.4 Software UpdateThe switch supports the software update function for the user to upgrade the firmware of the switch tothe latest software ver

-4-Table of Contents1. Introduction... 61.1 Features .

-40-3.4.5 LogoutBesides the Auto Logout Timer function described in the section of System Configuration, the switchalso allows the user to logout manu

-5-3.3 Monitoring ...323.3.1 Statistics O

-6-1. IntroductionBefore you start installing the switch, verify that the package contains the following:• Web Smart 24-Port 10/100/1000 Gigabit Ether

-7-1.2 View of Web Smart 24-Port Gigabit SwitchThe major user interface components on the front panel and rear panel are:• LED indicators LED Display

-8-1.3 Hardware SpecificationsStandard Compliance: IEEE802.3/802.3ab / 802.3z / 802.3u / 802.3xNetwork Interface:Configuration Mode Connector Port10/1

-9-1.4 Management Software SpecificationsInterface : Web Http browsingSystem configuration: IP address settings, system name, password, Auto-logout ti